+6012-2100 344


Name:   Password:

Products

MOS-620 Analog Oscilloscope

ENQUIRY




Download Brochure

Analog Oscilloscope
Model: MOS-620/MOS-640

Specification

Vertical system
Verticals resolution: 8bits (28point/DIV)
Accuracy: ± 3% ± 0.4mm ( × 5MAG: ± 5% ± 0.4mm)
Equivalent bandwidth: ± 3% ± 0.4mm( × 5MAG: ± 5% ± 0.4mm) -3dB, Sine Interpolate
Interpolation: Sine/Line
Horizontal System
Maximum Sample Rates: 20MS/s
Horizontal resolution: 10bit (100point/DIV)
Time base: 0.2μs/DIV~10s/DIV ( × 10MAG:1s/DIV~20ns/DIV)
Sweep mode: AUTO, NORM, ROLL.
Saved waveform expand rate: Maximum 100
Trigger
Trigger preset: DIV2, 5, 8
Acquisition
Dual Channel Acquisition:
10s/DIV~0.5s/DIV:CHOP; 0.2ms/DIV~0.2s/DIV: ALT
Acquisition Length: 1024Byte/CH
Display
View time: 0.2s~5s Adjustable
Display Memory Length: 1024Byte/CH
Reference Memory Length: 1024Byte/CH
RS232 interface transfer rate: 19200
VERTICAL AXIS
Sensitivity: 5mV~5V/DIV,10 steps in 1-2-5 sequence
Sensitivity accuracy:≤3% , (× 5 MAG:≤ 5% )
Vernier vertical sensitivity: To 1/2.5 or less of panel-indicated value
Frequency bandwidth: DC~20MHz( × 5MAG:DC~7MHz); AC coupling:Low limit frequency 10Hz.(With reference to 100KHz, 8DIV. Frequency response with-3dB.)
Rise time: Approx.17.5ns ( × 5MAG:Approx.50ns)
Input impedance: Approx.1MΩ /Approx.25pF
Square wave characteristics: Overshoot:≤ 5%(At 10mV/DIV range); Other distortions and other ranges:5% added to the above value
Dc balance shift: Adjustable on panel
Linearity: <± 0.1DIV of amplitude change when waveform of 2DIV at graticule center is moved vertically
Vertical modes:
CH1 single channel; CH2 single channel;
DUAL: CH1 and CH2 are displayed simultaneously. ALT or CHOP selectable at any sweep rate;
ADD:CH1+CH2 algebraic addition
Chopping repetition frequency: Approx.250KHz
Input coupling: AC, GND , DC
Maximum input voltage: 300Vpeak (AC: frequency 1KHz or lower);When set probe switch at 1:1, the maximum effective readout is 40Vpp(14Vrms at sine wave),or set probe switch at 10:1,the maximum effective readout is 400Vpp(140Vrms at sine wave).
Common mode rejection ratio: 50:1 or better at 50KHz sinusoidal wave.(When sensitivities of CH1 and CH2 are set equally)
Isolation between channels(At 5mV/DIV range): > 1000:1 at 50KHz;
> 30:1 at 20MHz
CH1 signal output: At least 20mV/DIV into a 50Ω termination. Bandwidth is 50Hz to at least 5MHz
CH2 INV BAL: Balanced point variation: ≤1DIV(Reference at center graticule)
TRIGGERING
Triggering source: CH1, CH2, LINE, EXT
Coupling: AC: 20Hz to 20MHz
Slope: +/-
Sensitivity: 20Hz~2MHz: 0.5DIV, TRIG-ALT:2DIV, EXT:200mV; 2~2MHz:1.5DIV TRIG-ALT:3DIV, EXT:800mV;
TV: Sync pulse more than 1DIV (EXT:1V)
Triggering modes: AUTO; NORM: TV-V: TV-H: (Both TV-V and TV-H synchronize only when the synchronizing signal is negative)
EXT triggering signal input: Input impedance/:Approx:1MΩ/approx.25pF; Max.input voltage 300V(DC+AC peak), AC: Frequency not higher than 1KHz
HORIZIONTAL AXIS
Sweep time: 0.2μ Sec~0.5Sec/DIV, 20steps in 1-2-5 sequence;
Sweep time accuracy: ± 3%; Vernier sweep time control: ≤ 1/2.5 of panel-indicated value;
Sweep magnification: 10 times; × 10MAG sweep time accuracy: ±5 %(20nSec~50nSec are uncalibrated);
Linearity: ± 3%, × 10MAG: ±5 %(20nSec~50nSec are uncalibrated);
Position shift caused by × 10MAG: Within 2DIV. at CRT screen center
X-Y MODE: Sensitivity: Same as vertical axis. (X-axis: CH1 input signal;Y-axis:CH2 input signal.); Frequency bandwidth: DC to at least 500KHz; X-Y phase difference:± 3°at DC-50KHz
Z AXIS
Sensitivity: 5Vp-p (Positive-going signal decreases intensity);
Frequency bandwidth: DC~2MHz; Input resistance: Approx.47KΩ ;
Maximum input voltage:3V(DC+AC peak, AC frequency≤1KHz)
CALIBRATION VOLTAGE
Waveform: Positive-going square wave;
Frequency: Approx.1KHz; Duty ratio: Within 48:52; Output voltage: 2Vp-p ± 2%;
Output impedance: Approx.1KHz
CRT
Type: 6-inch rectangular type, internal graticule; Phosphor: P31;Acceleration voltage: Approx.2KV; Effective screen size: 8 × 10DIV(1DIV=10mm(0.39in)); Graticule: Internal; Trace rotation: Provided

NOTE 

20MHz Dual Channel
High sensitivity 1mV/DIV
Z Axis Input
CH1 Output
10 times sweep magnification
TV Synchronization, X-Y mode
High luminance, internal graticule Toshiba CRT
Fmax=20MS/s
Store depth:1K × CH2+1K × 2(Reference Memories)
Preset triggering function, pre-trigger signal observation
Two channel, two reference waveform display Simultaneous 4 Waveforms Information
The minimum sweeping speed is 10s/DIV, The ration measures ultra low frequency signals
Measure and display Single shot, Non-period Signals Built in RS232 interface for communication with the computer Analog, ultra low speed and storage oscilloscope, three in one high performance with low price

Product Description

Specification

Vertical system
Verticals resolution: 8bits (28point/DIV)
Accuracy: ± 3% ± 0.4mm ( × 5MAG: ± 5% ± 0.4mm)
Equivalent bandwidth: ± 3% ± 0.4mm( × 5MAG: ± 5% ± 0.4mm) -3dB, Sine Interpolate
Interpolation: Sine/Line
Horizontal System
Maximum Sample Rates: 20MS/s
Horizontal resolution: 10bit (100point/DIV)
Time base: 0.2μs/DIV~10s/DIV ( × 10MAG:1s/DIV~20ns/DIV)
Sweep mode: AUTO, NORM, ROLL.
Saved waveform expand rate: Maximum 100
Trigger
Trigger preset: DIV2, 5, 8
Acquisition
Dual Channel Acquisition:
10s/DIV~0.5s/DIV:CHOP; 0.2ms/DIV~0.2s/DIV: ALT
Acquisition Length: 1024Byte/CH
Display
View time: 0.2s~5s Adjustable
Display Memory Length: 1024Byte/CH
Reference Memory Length: 1024Byte/CH
RS232 interface transfer rate: 19200
VERTICAL AXIS
Sensitivity: 5mV~5V/DIV,10 steps in 1-2-5 sequence
Sensitivity accuracy:≤3% , (× 5 MAG:≤ 5% )
Vernier vertical sensitivity: To 1/2.5 or less of panel-indicated value
Frequency bandwidth: DC~20MHz( × 5MAG:DC~7MHz); AC coupling:Low limit frequency 10Hz.(With reference to 100KHz, 8DIV. Frequency response with-3dB.)
Rise time: Approx.17.5ns ( × 5MAG:Approx.50ns)
Input impedance: Approx.1MΩ /Approx.25pF
Square wave characteristics: Overshoot:≤ 5%(At 10mV/DIV range); Other distortions and other ranges:5% added to the above value
Dc balance shift: Adjustable on panel
Linearity: <± 0.1DIV of amplitude change when waveform of 2DIV at graticule center is moved vertically
Vertical modes:
CH1 single channel; CH2 single channel;
DUAL: CH1 and CH2 are displayed simultaneously. ALT or CHOP selectable at any sweep rate;
ADD:CH1+CH2 algebraic addition
Chopping repetition frequency: Approx.250KHz
Input coupling: AC, GND , DC
Maximum input voltage: 300Vpeak (AC: frequency 1KHz or lower);When set probe switch at 1:1, the maximum effective readout is 40Vpp(14Vrms at sine wave),or set probe switch at 10:1,the maximum effective readout is 400Vpp(140Vrms at sine wave).
Common mode rejection ratio: 50:1 or better at 50KHz sinusoidal wave.(When sensitivities of CH1 and CH2 are set equally)
Isolation between channels(At 5mV/DIV range): > 1000:1 at 50KHz;
> 30:1 at 20MHz
CH1 signal output: At least 20mV/DIV into a 50Ω termination. Bandwidth is 50Hz to at least 5MHz
CH2 INV BAL: Balanced point variation: ≤1DIV(Reference at center graticule)
TRIGGERING
Triggering source: CH1, CH2, LINE, EXT
Coupling: AC: 20Hz to 20MHz
Slope: +/-
Sensitivity: 20Hz~2MHz: 0.5DIV, TRIG-ALT:2DIV, EXT:200mV; 2~2MHz:1.5DIV TRIG-ALT:3DIV, EXT:800mV;
TV: Sync pulse more than 1DIV (EXT:1V)
Triggering modes: AUTO; NORM: TV-V: TV-H: (Both TV-V and TV-H synchronize only when the synchronizing signal is negative)
EXT triggering signal input: Input impedance/:Approx:1MΩ/approx.25pF; Max.input voltage 300V(DC+AC peak), AC: Frequency not higher than 1KHz
HORIZIONTAL AXIS
Sweep time: 0.2μ Sec~0.5Sec/DIV, 20steps in 1-2-5 sequence;
Sweep time accuracy: ± 3%; Vernier sweep time control: ≤ 1/2.5 of panel-indicated value;
Sweep magnification: 10 times; × 10MAG sweep time accuracy: ±5 %(20nSec~50nSec are uncalibrated);
Linearity: ± 3%, × 10MAG: ±5 %(20nSec~50nSec are uncalibrated);
Position shift caused by × 10MAG: Within 2DIV. at CRT screen center
X-Y MODE: Sensitivity: Same as vertical axis. (X-axis: CH1 input signal;Y-axis:CH2 input signal.); Frequency bandwidth: DC to at least 500KHz; X-Y phase difference:± 3°at DC-50KHz
Z AXIS
Sensitivity: 5Vp-p (Positive-going signal decreases intensity);
Frequency bandwidth: DC~2MHz; Input resistance: Approx.47KΩ ;
Maximum input voltage:3V(DC+AC peak, AC frequency≤1KHz)
CALIBRATION VOLTAGE
Waveform: Positive-going square wave;
Frequency: Approx.1KHz; Duty ratio: Within 48:52; Output voltage: 2Vp-p ± 2%;
Output impedance: Approx.1KHz
CRT
Type: 6-inch rectangular type, internal graticule; Phosphor: P31;Acceleration voltage: Approx.2KV; Effective screen size: 8 × 10DIV(1DIV=10mm(0.39in)); Graticule: Internal; Trace rotation: Provided

NOTE 

20MHz Dual Channel
High sensitivity 1mV/DIV
Z Axis Input
CH1 Output
10 times sweep magnification
TV Synchronization, X-Y mode
High luminance, internal graticule Toshiba CRT
Fmax=20MS/s
Store depth:1K × CH2+1K × 2(Reference Memories)
Preset triggering function, pre-trigger signal observation
Two channel, two reference waveform display Simultaneous 4 Waveforms Information
The minimum sweeping speed is 10s/DIV, The ration measures ultra low frequency signals
Measure and display Single shot, Non-period Signals Built in RS232 interface for communication with the computer Analog, ultra low speed and storage oscilloscope, three in one high performance with low price

Category



Newsletter